DigitalDiagnost 4 High Performance (Stitching Patient Support) 712027
Class I - DangerousWhat Should You Do?
- Check if you have this product: Serial Numbers: SN17000294 SN17000295 SN17000114 SN17000185 SN17000362 SN17000263 SN17000264 SN17000399 SN15000017 SN17000235 SN18000001 SN17000414 SN17000376 SN16000352 SN17000311 SN17000070 SN14000079 SN14000080 SN17000044 SN17000346 SN14000052 SN17000045 SN17000351 SN17000038 SN17000262 SN17000126 SN15000122 SN17000100 SN17000422 SN17000359 SN16000390 SN15000048 SN17000084 SN16000386 SN17000106 SN17000288 SN17000278 SN17000335 SN16000394 SN16000387 SN17000151 SN17000352 SN17000329 SN17000349 SN17000303 SN17000334 SN17000216 SN17000305 SN17000398 SN15000328 SN17000289 SN17000411 SN17000436 SN17000090 SN15000006 SN17000179 SN17000034 SN17000231 SN16000355 SN17000166 SN17000127 SN16000421 SN16000398 SN14000105 SN16000430 SN16000418 SN17000150 SN17000092 SN15000054 SN15000097 SN15000110 SN17000373 SN15000132 SN14000040 SN14000045 SN15000098 SN16000435 SN15000142 SN15000151 SN17000141 SN15000410 SN15000417 SN16000402
- Do not eat it: Even if it looks and smells fine, do not consume this product.
- Throw it away or return it: You can return the product to the store for a full refund.
- Seek medical attention if needed: If you've consumed this product and feel unwell, contact your doctor immediately.
- Report problems: Report any issues to the FDA's Safety Reporting Portal.
⚠️ Emergency: If you experience severe symptoms after consuming this product, call 911 or Poison Control at 1-800-222-1222.
Recall Details
- Company:
- Philips Medical Systems Gmbh, DMC
- Reason for Recall:
- The hook does not securely hold the footplate in the vertical position. Therefore, the footplate can fall or swing down and injury operator or patient.
- Classification:
- Class I - Dangerous
Dangerous or defective products that predictably could cause serious health problems or death.
- Status:
- terminated
Product Information
Full Description:
DigitalDiagnost 4 High Performance (Stitching Patient Support) 712027
Product Codes/Lot Numbers:
Serial Numbers: SN17000294 SN17000295 SN17000114 SN17000185 SN17000362 SN17000263 SN17000264 SN17000399 SN15000017 SN17000235 SN18000001 SN17000414 SN17000376 SN16000352 SN17000311 SN17000070 SN14000079 SN14000080 SN17000044 SN17000346 SN14000052 SN17000045 SN17000351 SN17000038 SN17000262 SN17000126 SN15000122 SN17000100 SN17000422 SN17000359 SN16000390 SN15000048 SN17000084 SN16000386 SN17000106 SN17000288 SN17000278 SN17000335 SN16000394 SN16000387 SN17000151 SN17000352 SN17000329 SN17000349 SN17000303 SN17000334 SN17000216 SN17000305 SN17000398 SN15000328 SN17000289 SN17000411 SN17000436 SN17000090 SN15000006 SN17000179 SN17000034 SN17000231 SN16000355 SN17000166 SN17000127 SN16000421 SN16000398 SN14000105 SN16000430 SN16000418 SN17000150 SN17000092 SN15000054 SN15000097 SN15000110 SN17000373 SN15000132 SN14000040 SN14000045 SN15000098 SN16000435 SN15000142 SN15000151 SN17000141 SN15000410 SN15000417 SN16000402
Official Source
Always verify recall information with the official FDA source:
View on FDA.govFDA Recall Number: Z-2851-2018
Related Recalls
CombiDiagnost R90 Software Version R1.0 and R1.1
Philips Medical Systems Gmbh, DMC
Philips has become aware of a software issue, where the kV and mA values are not locked immediately but change when the collimator shutter position is changed directly after the Lock-In command. This software issue leads to an over or under exposed image.
CombiDiagnost GCF, Software v. 1.0.5, Product Code 709030 - Product Usage: Xray system, diagnostic, fluoroscopic, general purpose.
Philips Medical Systems Gmbh, DMC
When using the Table Up/Down button, the system may experience Error 80, which locks the geometry in that specific state, requiring the intervention of a service Engineer. Additionally, the thermos switch, which handles power down of the unit in case of transformer overheating, was installed incorrectly at production.
CombiDiagnost PCF, Software v. 1.0.5, Product Code 709030 - Product Usage: Xray system, diagnostic, fluoroscopic, general purpose.
Philips Medical Systems Gmbh, DMC
When using the Table Up/Down button, the system may experience Error 80, which locks the geometry in that specific state, requiring the intervention of a service Engineer. Additionally, the thermos switch, which handles power down of the unit in case of transformer overheating, was installed incorrectly at production.